Polybutadiene
From Wikipedia, the free encyclopedia
Polybutadiene is a synthetic rubber that is a polymer formed from the polymerization of the monomer 1,3-butadiene. It has a high resistance to wear and is used especially in the manufacture of tires. It has also been used to coat or encapsulate electronic assemblies, offering extremely high electrical resistivity. It exhibits a recovery of 80% after stress is applied, a value only exceeded by elastin and resilin.
Contents |
[edit] Polymerization of butadiene
1,3-Butadiene is an organic compound which is a rather simple conjugated diene hydrocarbon; the chemical structure is shown as a reactant in the diagram below. A hydrocarbon diene molecule has two carbon-carbon double bonds (i. e. between two sets of carbon atoms). Polybutadiene can be formed from many 1,3-butadiene monomers undergoing free radical polymerization to make a much longer polymer chain molecule.
A chain propagating step in this chemical reaction involves a free radical near the end of a growing polymer chain forming a covalent bond with the #1 carbon in a 1,3-butadiene monomer molecule being added, resulting in a polymer chain intermediate with a substituted allyl free radical at the end of the chain. This allyl free radical, formed from the butadiene just added, can further bond to another monomer molecule at either the #2 or #4 carbons of the previous butadiene monomer. Most of the time, the new monomer bonds to the #4 or terminal carbon of the previous butadiene, resulting in a 1,4-addition of the previous butadiene unit. In a 1,4-addition, the two double bonds of the previous butadiene unit are turned into single bonds and a new double bond is formed between the #2 and #3 carbons. This new double bond may have either a cis or a trans configuration. A smaller fraction of the time (perhaps 20%), the new monomer bonds to the #2 carbon of the previous butadiene, resulting in a 1,2-addition of the previous butadiene unit. The double bond between the #1 and #2 carbons turns into a single bond in the previous butadiene unit, and the double bond between the #3 and #4 carbons remains intact in a short vinyl side group available for branching or cross-linking. Cis or trans configurations are not applicable in 1,2-additions of butadiene. See the following reaction diagram for examples of 1,2- and 1,4-addition in a polybutadiene chain.
The trans double bonds formed during polymerization allow the polymer chain to stay rather straight, allowing sections of polymer chains to line up against each other and effectively form microcrystalline regions in the material. The cis double bonds cause a bend in the polymer chain, preventing polymer chains from lining up and forming crystalline regions and resulting in larger regions of amorphous polymer. It has been found that a substantial percentage of cis double bond configurations in the polymer will result in a material with flexible elastomer (rubber-like) qualities. In free radical polymerization, both cis and trans double bonds will form in percentages which depend on temperature. There are different catalysts available which can result in polymerization either in the cis or the trans configurations.
[edit] Properties
Polybutadiene rubber is a highly resilient synthetic rubber. Due to outstanding resilience, it can be used for the manufacturing of golf balls. Heat build up will be less in polybutadiene rubber based vulcanizate subjected to repeated flexing during service. This property leads to the use in the sidewall of the truck tires. Good abrasion resistance of this rubber leads to the use in tread portion of truck tires; however, skidding may be the problem in passenger car tires due to low rolling resistance. For high temperature curing, polybutadiene rubber may be blended with natural rubber and other rubbers, due to resistance in reversion of physical properties. Polybutadiene rubber can be used in water seals for dam due to its low water absorption properties. Rubber bullets and road binders can be also produced by polybutadiene rubber.
[edit] Copolymers
1,3-butadiene is normally copolymerized with other types of monomers such as styrene and acrylonitrile to form rubbers or plastics with various qualities. The most common form is styrene-butadiene copolymer, which is a commodity material for car tires. It is also used in block copolymers and tough thermoplastics such as ABS plastic. This way a copolymer material can be made with good stiffness, hardness, and toughness. Because the chains have a double bond in each and every repeat unit, the material is sensitive to ozone cracking.
[edit] See also
[edit] References
 |
This article does not cite any references or sources. (May 2008) Please help improve this article by adding citations to reliable sources. Unverifiable material may be challenged and removed. |
